You are here: Start » Function Reference » Computer Vision » Shape Fitting » FitPathToStripe_Direct

FitPathToStripe_Direct

Header:	AVL.h
Namespace:	avl
Module:	MetrologyPro

Performs a series of 1D stripe detections and creates a path from the detected points.

Applications: Tracing of a stripe, whose rough location and shape is known beforehand.

Syntax

void avl::FitPathToStripe_Direct
(
	const avl::Image& inImage,
	const avl::PathFittingField& inFittingField,
	atl::Optional<const avl::CoordinateSystem2D&> inFittingFieldAlignment,
	atl::Optional<float> inScanStep,
	int inScanWidth,
	const avl::SamplingParams& inSamplingParams,
	const avl::StripeScanParams& inStripeScanParams,
	avl::Selection::Type inStripeSelection,
	atl::Optional<const avl::LocalBlindness&> inLocalBlindness,
	atl::Optional<int> inMaxInterpolationLength,
	atl::Optional<float> inMaxDeviationDelta,
	float inMaxIncompleteness,
	atl::Conditional<avl::Path>& outPath,
	atl::Conditional<avl::Path>& outLeftPath,
	atl::Conditional<avl::Path>& outRightPath,
	atl::Array<atl::Conditional<avl::Stripe1D> >& outStripes,
	atl::Optional<atl::Conditional<avl::Profile>&> outDeviationProfile = atl::NIL,
	atl::Optional<avl::PathFittingField&> outAlignedFittingField = atl::NIL,
	atl::Array<avl::Segment2D>& diagScanSegments,
	atl::Array<avl::Rectangle2D>& diagSamplingAreas,
	atl::Array<avl::Profile>& diagBrightnessProfiles,
	atl::Array<avl::Profile>& diagResponseProfiles
)

Parameters

Name	Type	Range	Default	Description
inImage	const Image&			Image to fit the path to
inFittingField	const PathFittingField&			Path fitting field
inFittingFieldAlignment	Optional<const CoordinateSystem2D&>		NIL	Adjusts the fitting field to the position of the inspected object
inScanStep	Optional<float>	0.0 -	5.0f	Optional implicit conversion of the input path to an equidistant one
inScanWidth	int	1 -	5	The width of each scan field (in pixels)
inSamplingParams	const SamplingParams&			Parameters controlling the sampling process
inStripeScanParams	const StripeScanParams&		StripeScanParams ( ProfileInterpolation: Quadratic4 SmoothingStdDev: 0.6f MinMagnitude: 5.0f MaxInnerEdgeMagnitude: Nil StripePolarity: Dark MinStripeWidth: 0.0f MaxStripeWidth: Nil )	Parameters controlling the stripe extraction process
inStripeSelection	Selection::Type			Selection mode of stripe
inLocalBlindness	Optional<const LocalBlindness&>		NIL	Defines conditions in which weaker edges can be detected in the vicinity of stronger edges
inMaxInterpolationLength	Optional<int>	0 -	1	Maximal number of consecutive points not found
inMaxDeviationDelta	Optional<float>	0.0 -	NIL	Maximal difference between deviations of consecutive path points
inMaxIncompleteness	float	0.0 - 0.999	0.1f	Maximal fraction of stripe points not found
outPath	Conditional<Path>&			Fitted path in the middle of found stripe
outLeftPath	Conditional<Path>&			Fitted left path
outRightPath	Conditional<Path>&			Fitted right path
outStripes	Array<Conditional<Stripe1D> >&			Found stripes
outDeviationProfile	Optional<Conditional<Profile>&>		NIL	Profile of distances between the actual path points and the corresponding reference path points
outAlignedFittingField	Optional<PathFittingField&>		NIL	Fitting field used; in the image coordinate system
diagScanSegments	Array<Segment2D>&			Segments along which the scans were run
diagSamplingAreas	Array<Rectangle2D>&			Areas from which the input image is sampled
diagBrightnessProfiles	Array<Profile>&			Extracted image profiles
diagResponseProfiles	Array<Profile>&			Profiles of the edge (derivative) operator response

Optional Outputs

The computation of following outputs can be switched off by passing value atl::NIL to these parameters: outDeviationProfile, outAlignedFittingField.

Description

The operation tries to fit a given path to stripe present in the inImage image. Internally, it performs a series of scans with the ScanSingleStripe_Direct filter along a number of specific scan segments which length is always equal to the inFittingField width and cannot be less than 4. The found points are then used to determine the actual position of the path in the image. Only inMaxIncompleteness fraction of these scans may fail. If the fitting according to the given parameters is not possible, outPath is set to Nil.

There are also another parameters that control the path fitting process. The inMaxDeviationDelta parameter defines the maximal allowed difference between deviations of consecutive points from the input path points. If some of the scans fail or if some of found points are classified to be wrong according to another control parameters, output path points corresponding to them are interpolated depending on points in their nearest vicinity. No more than inMaxInterpolationLength consecutive points can be interpolated. The exception to this behavior are points which were not found on both ends of the input path. Those are not part of the result at all.

Hints

Connect an input image to the inImage input.
Define inStripeScanParams.StripePolarity to detect a particular stripe type, and only that type.
Adjust inStripeScanParams.MinStripeWidth and inStripeScanParams.MaxStripeWidth to the expected thickness of the stripe (in pixels).
If no or too few stripe points are found, try decreasing inStripeScanParams.MinMagnitude.
If some of the scans may fail, set the inMaxIncompleteness input accordingly.
Use the outStripes outputs to visualize the scanning results.

Examples

Fitting a path to a dark stripe
(inStripeScanParams.SmoothingStdDev = 2.0, inStripeScanParams.MinStripeWidth = 15.0, inStripeScanParams.StripePolarity = Dark).

Remarks

Read more about Local Coordinate Systems in Machine Vision Guide: Local Coordinate Systems.

This filter is a part of the Shape Fitting toolset. To read more about this technique, one can refer to the Shape Fitting chapter of our Machine Vision Guide

Hardware Acceleration

This operation supports automatic parallelization for multicore and multiprocessor systems.